Airlink101 AWLL7025 Bedienungsanleitung

Dual Band Wireless N USB Adapter Model # AWLL7025 User’s Manual Rev. 1.0

10 Step 4 Verify that the Authentication Mode and Input Method match to your wireless router’s settings and click Next. Step 5 Input the encryptio

11 Step 6 Keep the default IP Setting and click Complete. Step 7 You should see a blue circle around the antenna icon indicating a valid connection

12 Step 8 Go to the Link Information tab and click on the More button. Step 9 Verify that you are receiving adequate Signal Strength and Link Quali

13 If you do not have adequate Signal Strength, try re-orienting the Access Point and/or the USB Adapter by using the USB Extension Cable included in

14 4. Use Wireless Monitor Utility This section describes the various functions of the Wireless Monitor Utility that you can configure, including the

15 The Wireless Information displays the current wireless network you are connected to as well as various other statuses such as the Signal Strengt

16 4.2 AP List The AP List tab displays all the available wireless networks detected by the USB Adapter. Simply select the desired wireless network y

17 4.3 Configure Encryption Settings This section describes how to configure encryption settings for the Dual Band Wireless N USB adapter. Note: The

18 Step 2 Verify the Profile Name is correct and click Next. Step 3 Verify the Network Name (SSID) is correct and click Next.

19 For WEP Settings: WEP Step 4.1 Select the appropriate Authentication Mode and Encryption settings and click Next. WEP Step 4.2 Enter the appro

2 Table of Contents 1. Introduction ...

20 For WPA-PSK and WPA2-PSK Settings: WPA Step 4.1 Select WPA-PSK or WPA2-PSK and the appropriate Input Method and click Next. WPA Step 4.2 Enter

21 Step 5 Keep the default IP Setting and click Complete to finish the settings. Step 6 You should see a blue circle around the antenna icon indica

22 4.4 Profile Setting The Profile Setting tab lists all the profiles you have created. You can create new profiles for different network environment

23 Step 3 Enter the SSID (Network Name) of the wireless network you want to connect to and click Next. Step 4 Configure any encryption setting if r

24 Step 5 Keep the default IP Setting and click Complete to finish the profile setting. Step 6 Your new profile will be listed in the Profile List.

25 4.5 Configure IP Setting To change the IP settings of the wireless adapter, follow the steps below: Step 1 On the last step of 4.4 Profile Settin

26 4.6 WiFi Protected Setup (WPS) Airlink101 Dual Band Wireless N USB Adapter has an innovated built-in WPS (WiFi-Protected Setup) feature which can

27 Step 3 The Router will now start the handshake with the wireless adapter. When you see the window below, the wireless connection has been establis

28 Step 2 Click on Rescan button. The wireless router or AP you wish to connect to should appear in the list. Write down the PIN code on a piece of pa

29 The router will start to search for the WPS enabled device with matching PIN code. Step 5 Select the Router/AP you want to connect to and click

3 1. Introduction Thank you for purchasing Airlink101 Dual Band Wireless N USB Adapter. The AWLL7025 Dual Band Wireless N USB Adapter can operate on

30 4.7 About The About tab shows the Utility, Driver, and Firmware version as well as the MAC address of the Dual Band Wireless N USB Adapter.

31 Appendix A – Specifications Standards • IEEE 802.11n draft 2.0 • IEEE 802.11 a / b / g Frequency Ban

32 Appendix B – Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limit

33 This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause

34 Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part

35 [French] exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [nome del cos

36 Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Web Site: www.airlink101.com *Theoreti

4 2. Install Utility and Driver This Quick Installation Guide only provides the basic installation instructions. For detailed installation instructio

5 Note: If the Autorun screen doesn’t appear automatically go to Start, Run, and type D:\Utility\Setup.exe (where D is the letter of your CD drive) an

6 Step 5 Click Next to begin the installation. Step 6 Give Permission to Window to install the driver software For Windows Vista, click the Instal

7 3. Configure the Adapter This section describes how to connect your Dual Band Wireless N USB Adapter to a wireless network. Note to Windows XP Use

8 Open the Airlink101 Wireless Monitor utility by double clicking on the Airlink101 Wireless Monitor Utility icon in the system tray at the bottom ri

9 Step 2 If encryption is not enabled for the selected access point / router, skip to step 7. Otherwise, enter a Profile Name for your wireless settin