Airlink101 AP411W Bedienungsanleitung Seite 1

Model # AP411W User’s Manual Ver. 1A

10Step 8 To setup SSID and WEP encryption, click on the Setup Wizard link and click Next. Step 9 The default SSID is default and the default chann

11Step 10 Select to enable or disable WEP encryption and click Next. If you already have WEP encryption enabled for your existing wireless network

12Web Configuration Utility The Web configuration utility allows you to configure settings for the Access Point. In order to access the web configur

13Advanced Setup Use the list on the left side of the screen to navigate to the desired page. Configuration – IP Address MAC Address: Displays

14Default Gateway: This field is optional. If you have a router on your network, enter the IP address of your router. Click Apply to save any change

15Configuration – AP Mode Settings Access Point: This is the default setting. It connects the wireless clients to the wired part of your network.

16Configuration – WLAN Parameter Settings Wireless Band: Select to set the signal to 802.11g or 802.11g/802.11b. SSID: The name designated for a

17Fragment Length: The fragmentation threshold, which is specified in bytes, determines whether packets will be fragmented. Packets exceeding the 234

18Configuration – WLAN Partition Wireless Band: Select to set the signal to 802.11g or 802.11g/802.11b. Internal Station Connection: Check Enable

19Control: • Disabled: disables the filter function • Accept: only accepts connection from the devices whose MAC Address are listed in the Access C

2Table of Contents Package Contents ... 3 Intr

20 Key Type: For WEP encryption, select to use HEX (limited to 0-9, A-F) or ASCII (any number or letter). Key Size: 64 Bits: 10 HEX characters or

21WPA Mode Select WPA as the Authentication and click Apply. Select PSK then enter the pass phrase in the Pass Phrase field. Note: Pass phrase

22Additional WPA settings (RADIUS Server Required) If you have a RADIUS Server in your network, you may choose to use EAP as the WPA Mode. Domain

23Management – Administration User Name: Enter a user name for the login screen; admin is the default setting. Old Password: To change your pass

24Management – Misc Telnet Service: Check Enabled to allow Telnet Service through the Access Point. Timeout: Select the timeout interval. Default

25Maintenance – Configuration File You can save your configurations to a file and upload the file later (i.e. after a factory reset so you don’t h

26Statistics This window displays the statistics of the wireless local area network. Throughput: displays the throughput statistics. Transmitted

27Received Frame Count: displays the received frame count. WEP Frame Error: displays the WEP Frame Error.

28Troubleshooting This section provides solutions to problems that can occur during the installation and operation of the 108Mbps SuperG Wireless Acc

293. What variables may cause my wireless products to lose reception? Our wireless products let you access your network from virtually anywhere you

3Package Contents • Wireless 108Mbps SuperG Access Point • Power Adapter-DC 5V, 2.0A • Quick Installation Guide • Ethernet Cable • One Set of SM

30 To hard-reset the 108Mbps SuperG Wireless Access Point to the Factory Default Settings, please do the following: A. Locate the Reset button

31Technical Specifications Standards  IEEE 802.11g  IEEE 802.11  IEEE 802.11b  IEEE 802.3  IEEE 802.3u Device Management  Web-Based Interne

32Receiver Sensitivity:  54Mbps OFDM, 10% PER, -68dBm  48Mbps OFDM, 10% PER, -68dBm  36Mbps OFDM, 10% PER, -75dBm  24Mbps OFDM, 10% PER, -79dBm 

4Connections LEDs Power: Solid green indicates power is on. LAN: Solid green indicates an established connection. Blinking green ind

5Wireless Basics Installation Considerations The 108Mbps SuperG Wireless Access Point lets you access your network, using a wireless connection, fro

6Connecting the Access Point Step 1 Connect one end of a network cable to the Ethernet port of the access point and connect the other end of the cab

7Establishing Wireless Connection Below are the default wireless settings of the access point. You must configure your wireless network adapter to t

8Step 2 Right-click on either Wireless Network Connection (if you’re using a wireless card to connect to the AP), or Local Area Connection (if you’re

9Step 4 Select Use the following IP address and enter an IP address of 10.0.0.x (where x is any number between 2 - 254). Also enter 255.0.0.0 for the