Airlink101 APO1010 Bedienungsanleitung PDF herunterladen (Seite 46)

 SNMP Trap : Events such as cold start, interface up & down, and association & disassociation will report to an assigned

server.

Î Community : Set a community string required by the remote host computer that will receive trap messages or

notices send by the system.

Î IP : Enter the IP addresses of the remote hosts to receive trap messages.

Click Save button to save changes and click Reboot button to activate.

1 2 ... 41 42 43 44 45 46 47 48 49 50 51 ... 167 168

Table of Contents 2
Chapter 1. System Overview 6
1.2 System Concept 7
Example 1 : Point-to-Point 9
APO1000/APO1010 10
Configuration in CPE Mode 11
1.4 Product Benefit 13
1.5 Specification 14
2.1 Hardware Installation 17
¾ APO1000 18
¾ APO1010 19
Front Panel Rear Panel 20
 Login Success 22
3.1.1 Network Requirement 23
3.1.2 Configure LAN IP 24
3.2.1 Wireless General Setup 26
3.2.3 Create Virtual AP(VAP) 30
3.2.3.2 Virtual AP Setup 31
3.2.4 MAC Filter Setup 37
3.4 System Management 41
3.4.2 Configure System Time 43
3.4.3 Configure UPnP 44
3.4.4 Configure SNMP Setup 45
3.4.6 Firmware Upgrade 48
3.4.7 Network Utility 49
3.4.8 Reboot 50
3.5 System Status 51
3.5.3 WDS Link Status 54
3.5.4 Extra Information 55
3.5.5 Event Log 57
4.1.1 Network Requirement 58
4.1.2 Configure LAN IP 59
4.2.3 WDS Setup 65
 WDS MAC List 67
4.3 System Management 68
4.3.2 Configure System Time 70
4.3.3 Configure UPnP 71
4.3.4 Configure SNMP Setup 72
4.3.6 Firmware Upgrade 75
4.3.7 Network Utility 76
4.3.8 Reboot 77
4.4 System Status 78
4.4.2 WDS Link Status 80
4.4.3 Extra Information 81
4.4.4 Event Log 83
5.1.1 Network Requirement 84
5.1.3 Configure DDNS Setup 89
5.1.4 Configure LAN IP 90
5.2 Access Point Association 92
5.2.3 Site Survey 98
5.3 System Management 99
5.3.2 Configure System Time 101
5.3.3 Configure UPnP 102
5.3.4 Configure SNMP Setup 103
5.3.6 Firmware Upgrade 106
5.3.7 Network Utility 107
5.3.8 Reboot 108
5.4 Access Control List 109
5.4.2 MAC Filter Setup 111
5.5 Resource Sharing 112
5.6 System Status 115
5.6.2 DHCP Clients 118
5.6.3 Extra Info 119
5.6.4 Event Log 121
Configuration 122
6.1.2 Configure LAN IP 123
6.2 Access Point Association 125
RTS/CTS 128
6.2.3 Site Survey 130
6.3.1 AP Setup 131
6.3.2 MAC Filter Setup 137
6.4 System Management 138
6.4.2 Configure System Time 140
6.4.3 Configure UPnP 141
6.4.4 Configure SNMP Setup 142
6.4.6 Firmware Upgrade 145
6.4.7 Network Utility 146
6.4.8 Reboot 147
6.5 System Status 148
6.5.3 DHCP Clients 152
6.5.4 Extra Information 153
6.5.5 Event Log 155
7.2 Using the CLI 157
Windows XP 159
Technical Support 168

Kommentare zu diesen Handbüchern

Keine Kommentare

Airlink101 APO1010 Bedienungsanleitung Seite 46

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Airlink101 APO1010