Airlink101 AR660W3G Bedienungsanleitung

Wireless N 3G/3.5G Mobile Router Model # AR660W3G User’s Manual Ver. 1A

11 Step 3 Click on Setup Wizard. Step 4 Configure the Time Zone Settings of the Router. Click Next.

12 The Time Zone allows your router to base its time on the settings configured here, this will affect functions such as Log entries and Firewall se

13 3G/3.5G Click on 3G/3.5G if you are connecting to Internet through a 3G USB modem. When the 3G/3.5G detailed settings come up, enter the Interne

14 PIN Code Please input Pin Code for your UMTS or HSDPA or EVDO connection, this is optional, and only required if your service provider asks you to

15 DSL For DSL users, your Internet type is either Dynamic IP or PPPoE. If you are not sure which one you have, it is suggested to select PPPoE xDS

16 2) “Connect on Demand” - only connects to Internet when there’s a connect attempt. 3) ‘Manual’ - only connects to Internet when ‘Connect’ button on

17 PPTP PPTP xDSL requires two kinds of setting: WAN interface setting (setup IP address) and PPTP setting (PPTP user name and password). Here w

18 PPTP Gateway Please input the IP address of PPTP gateway assigned by your Internet service provider here. Connection ID Please input the c

19 Parameter Description User Name Please input user name assigned by your Internet service provider here. Password Please input the pass

20 Assign login server manually Check this box to choose login server by yourself. Server IP Address Please input the IP address of login server he

Federal Communication Commission Interference Statement FCC Part 15 This equipment has been tested and found to comply with the limits for a Class B

21 Channel Number Select a channel from the dropdown list of ‘Channel Number’ for broadcasting. You can choose any channel number you want to use, an

22 Click OK to save the settings. WEP Enter the settings below: • Key Length: Select 64-bit or 128-bit • Key Format: Select ASCII or Hex • De

23 After 30 seconds, you will go back to the Status page with valid IP address assigned by you ISP (or configured by yourself if you use Static IP) in

24 Step 3 Enter the Security key you configured for the Router (see Step 8 in Section 2). Click Connect. Step 4 Click on Close. Now the wireless

25

26 2.4 Troubleshooting If you have trouble connecting to the Internet with Cable/DSL modem, try the following steps: Step 1 Power off the Cable/DSL m

27

28 Chapter 3 Using Web Configuration Utility The Web Configuration Utility contains advanced features that allow you to configure the router to meet

29 3.1 Network 3.1.1 WAN Use the WAN setting page to change your Internet connection type. The WAN setting page allows you to configure the Internet

30 Note: The setting shown above is for Verizon 720 USB Modem. Parameter Description PIN Code Please input Pin Code for your UMTS or HSDPA or E

Table of Contents FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT ... 2 TABLE OF CONTENTS ...

31 ¾ LAN IP section Parameters Default Description IP address 192.168.2.1 This is the router’s LAN IP address

32 ¾ Static DHCP Lease Table section This function allows you to assign a static IP address to a specific computer forever, so you don’t have to set

33 After you clicked Apply, the following message will be displayed on your web browser: You can click “Continue” to back to previous setup page t

34 You can click “Continue” to back to previous setup page to continue on other setup procedures, or click “Apply” to reboot the router so the setti

35 After you clicked Apply, the following message will be displayed on your web browser: You can click “Continue” to back to previous setup page t

36 You can click “Continue” to back to previous setup page to continue on other setup procedures, or click “Apply” to reboot the router so the setting

37 clients, maximum 54Mbps for 802.11g clients, and maximum 300Mbps for 802.11n clients*). SSID airlink101 This is the

38 Parameters Default Description Encryption You can choose Disable, WEP, WPA pre-share key, WPA RADIUS for encryption mode. Enable 802.1x Aut

39 Parameters Description Key Length You can select the WEP key length for encryption, 64-bit or 128-bit. Larger WEP key length will provide h

40 Parameters Description WPA Unicast Cipher Suite Available options are: WPA (TKIP), WPA2 (AES), and WPA2 Mixed. You can select one of them, b

3.5 SECURITY...64 3.5.1

41 Parameters Description WPA Unicast Cipher Suite Please select a type of WPA cipher suite. Available options are: WPA (TKIP), WPA2 (AES),

42 Parameters Description Delete If you want to delete a specific MAC address entry, check the ‘select’ box of the MAC address you want to dele

43 Parameters Description Fragment Threshold “Fragment Threshold” specifies the maximum size of packet during the fragmentation of data to be t

44 Broadcast ESSID Decide if the wireless router will broadcast its own ESSID or not. You can hide the ESSID of your wireless router by selecting “Di

45 Please make sure this feature is enabled on the Router (see the screenshot above). In the instructions below, we are going to use the Airlink101

46 Step 4 The Router will now start the handshake with the wireless adapter which will take about 30 seconds. When you see the window similar to th

47 here. If wireless security function has not been set, you’ll see “unConfigured”. Self PIN code: This is the WPS PIN code of this wireless router.

48 3.3 Application & Gaming 3.3.1 Port Forwarding The Port Forwarding allows you to re-direct a particular range of service port numbers (from t

49 Delete Selected If you want to delete a setting, check the ‘select’ box of the setting you want to delete, then click ‘Delete Selected’ button.

50 Parameter Description Enable Port Triggering Check to enable Port Triggering, or uncheck to disable. IP Address This is the pri

6 Chapter 1 Introduction Congratulations on your purchase of AR660W3G Wireless N 3G/3.5G Mobile Router. This product is specifically designed for bus

51 Delete Selected If you want to delete a setting, check the ‘select’ box of the setting you want to delete, then click ‘Delete Selected’ button. (

52 Parameters Description Enable DMZ Check/uncheck to enable/disable DMZ. Public IP You can select “Dynamic IP” or “Static IP” here. If y

53 Reset You can also click “Reset”‟ button to unselect all DMZ entries. After you finish with all settings, please click “Apply” button. If you w

54 If you want to reset all settings in this page, please click “Cancel” button. After you clicked Apply, the following message will be displayed on

55 Enable QoS Check this box to enable QoS, and uncheck this box to disable QoS. Total Download Bandwidth You can set the limit of total download b

56 Parameter Description Rule Name Please give a name to this QoS rule (up to 15 alphanumerical characters). Bandwidth Set the ban

57 (destination) IP address and /or port number is universal, just leave it blank. Traffic Type Please select the traffic type of this rule, availa

58 3.4 Access Restrictions This function allows you to configure some Internet access rules for your local computers based on the IP addre

59 3.4.1.1 MAC Filtering If you want to restrict users from accessing certain Internet applications/services (e.g. Internet websites, email, FTP et

60 Comment You can input any text here as the comment of this MAC address, like ‘ROOM 2A Computer’. Add Click “Add” button to add the MAC address

7 Back Panel LED Light Status Description POWER On Router is powered on. On WPS setup is in progress. Off Wire

61 Click Add PC to add a new IP address to IP filtering table, up to 20 IP addresses can be added. Parameters Description Client PC Descriptio

62 Protocol If the service you need is not listed above, you can create a new service on your own. Please select TCP or UDP, if you’re not sure, plea

63 Parameter Description Enable URL Filtering Enable/Disable URL Blocking. URL/Keyword You can enter the full URL address of a websi

64 3.5 Security 3.5.1 Firewall Excepting NAT, this router also provides firewall function to block malicious intruders from accessing your computers

65 Parameter Description IPsec pass through Check this box and the router will enable IPsec packets pass through the router

66 Sync Flood Like Ping of Death, you can set the threshold of when this DoS prevention mechanism will be activated. 3.6 Administration The Adm

67 You can click “Continue” to back to previous setup page to continue on other setup procedures, or click “Apply” to reboot the router so the setti

68 After you clicked Apply, the following message will be displayed on your web browser: You can click “Continue” to back to previous setup page t

69 If you want to reset all settings in this page, please click “Cancel” button. After you clicked Apply, the following message will be displayed on y

70 NOTE: Never interrupt the upgrade process by closing the web browser or physically disconnect your computer from router. If the firmware you uploa

8 Item Name Description Antenna A/B These antennas are 3dBi dipole antennas. Radio ON/OFF Switch the button to activate or deactivate the Router’s w

71 3.6.7 System Log All important system events are logged. You can use this function to check the event log of your router. Parameters Descrip

72 Parameters Description Save Save current event log to a text file. Clear Delete all event logs displayed here. Refresh Refresh the e

73 3.6.10 UPnP Check the box to enable UPnP feature here. After you enable the UPnP feature, all client systems that support UPnP, like Windows XP, c

74 3.7 Status The Status section allows you to monitor the current status of your router. You can use the Status page to monitor: the Internet, LAN c

75 3.7.3 Wireless Status You can use this function to show the Wireless LAN status of your router, including ESSID (the name of your wireless networ

76

77 Technical Support E-mail: [email protected] Toll Free: 1-888-746-3238 Website: www.airlink101.com * The AR660W3

9 Chapter 2 Connecting the Router 2.1 Building Network Connection Note: Prior to connecting the router, be sure to power off your computer, DSL/Cabl

10 Step 3 Plug the power adapter to the router and connect it to an outlet or power strip. Step 4 Power on your computer. Step 5 Make sure the Power